Procedure
Number |
Test Method |
| QC 1 (PDF 1.2 MB) |
Standard Practice for Cement Producers That Certify Portland Cement |
| QC 2 (PDF 1.2 MB) |
Standard Practice for Asphalt Suppliers That Certify Performance Graded Asphalts |
| QC 3 (PDF 1.0 MB) |
Quality System Laboratory Review |
| QC 4 (PDF 1.0 MB) |
Standard Practice for Fly Producers/Importers/Distributors That Certify Fly Ash |
| QC 5 (PDF 1.3 MB) |
Standard Practice for Ground Granulated Blast-Furnace Slag Producers/Importers/Distributors That Certify Ground Granulated Blast-Furnace Slag |
| T 2 (PDF 404 kb) |
FOP for AASHTO for Sampling of Aggregate |
| TM 2 (PDF 1.2 MB) |
FOP for WAQTC for Sampling Freshly Mixed Concrete |
| TM 8 (PDF 1.2 MB) |
FOP for WAQTC for In-Place Density of Bituminous Mixes Using the nuclear Moisture-Density Gauge |
| T 19 (PDF 1.0 MB) |
Unit Weight and Voids in Aggregates (Checklist Only) |
| T 22 (PDF 1.4 MB) |
FOP for AASHTO for Compressive Strength of Cylindrical Concrete Specimens |
| T 23 (PDF 1.4 MB) |
FOP for AASHTO for Making and Curing Concrete test Specimens in the Field |
| T 27/T 11 (PDF 637 KB) |
FOP for WAQTC/AASHTO for Sieve Analysis of Fine and Coarse Aggregates |
| T 40 (PDF 1.2 MB) |
FOP for WAQTC/AASHTO for Sampling Bituminous Materials |
| T 90 (PDF 1.0 MB) |
Determining the Plastic Limit and Plasticity Index of Soils (Checklist Only) |
| T 99 (PDF 1.4 MB) |
FOP for AASHTO for Moisture-Density Relations of Soils Using a 5.5-lb (2.5-kg) Rammer and a 12 in (305 mm) Drop |
| T 106 (PDF 1.2 MB) |
FOP for AASHTO for Compressive Strength of Hydraulic Cement Mortars (Using 2 in or (50 mm) Cube Specimens) |
| T 112 (PDF 1.0 MB) |
Clay Lumps and Friable Particles in Aggregates |
| T 113 (PDF 1.3 MB) |
Method of Test for Determination of Degradation Value |
| T 119 (PDF 1.2 MB) |
FOP for AASHTO for Standard Test Method for Slump of Hydraulic-Cement Concrete |
| T 121 (PDF 1.2 MB) |
Density (Unit Weight), Yield and Air Content (Gravimetric) of Concrete |
| T 123 (PDF 1.1 MB) |
Method of Test for Bark Mulch |
| T 125 (PDF 1.1 MB) |
Determination of Fiber Length Percentages in Wood Strand Mulch |
| T 126 (PDF 1.0 MB) |
Determination of Fiber Length Percentages in Hydraulically-Applied Erosion Control Products |
| T 127 (PDF 1.1 MB) |
Preparation of Leachate Sample for Testing of HECP Effluents |
| SOP 128 (PDF 1.1 MB) |
Sampling For Aggregate Source Approval |
| T 152 (PDF 1.2 MB) |
FOP for WAQTC/AASHTO for Air Content of Freshly Mixed Concrete by the Pressure Method |
| T 166 (PDF 467) |
FOP for AASHTO for Bulk Specific Gravity of Compacted Bituminous Mixtures Using Saturated Surface-Dry Specimens |
| T 168 (PDF 1.4 MB) |
FOP for WAQTC/AASHTO for Sampling Hot Mix Asphalt |
| T 176 (PDF 1.5 MB) |
FOP for AASHTO for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test |
| T 180 (PDF 2.5 MB) |
FOP for AASHTO for Moisture-Density Relations of Soils Using a 10 lb (4.54 kg) Rammer and an 18 in (457 mm) Drop |
| T 196 (PDF 1.0 MB) |
Air Content of Concrete (Volumetric Method) (Checklist Only) |
| T 209 (PDF 471 kb) |
FOP for AASHTO for Method of Test for Maximum Specific Gravity of Hot Mix Asphalt — “Rice Density” |
| T 217 (PDF 1.2 MB) |
FOP for AASHTO for Determination of Moisture in Soils by means of a Calcium Carbide Gas Pressure Moisture Tester |
| T 231 (PDF 1.4 MB) |
FOP for AASHTO for Capping Cylindrical Concrete Specimens |
| T 248 (PDF 1.3 MB) |
FOP for AASHTO for Reducing Samples of Aggregate to Testing Size |
| T 255 (PDF 1.3 MB) |
FOP for AASHTO for Total Moisture Content of Aggregate by Drying |
| T 265 (PDF 1.0 MB) |
Laboratory Determination of Moisture Content of Soils |
| T 272 (PDF 1.2 MB) |
FOP for AASHTO for Family of Curves — One Point Method |
| T 288 (PDF 1.0 MB) |
Determining Minimum Laboratory Soil Resistivity(checklist only) |
| T 304 (PDF 1.5 MB) |
FOP for AASHTO for Uncompacted Void Content of Fine Aggregate |
| T 307 (PDF 1.2 MB) |
Resilient Modulus of Subgrade Soils and Untreated Base/Subbase Materials |
| T 308 (PDF 1.3 MB) |
FOP for AASHTO for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method |
| T 309 (PDF 1.2 MB) |
FOP for WAQTC/ AASHTO for Temperature of Freshly Mixed Portland Cement Concrete |
| T 310 (PDF 1.2 MB) |
FOP for AASHTO for In-Place Density and Moisture Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
| T 312 (PDF 1.2 MB) |
FOP for AASHTO for Preparing and Determining the Density of Hot-Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| T 313 (PDF 1.1 MB) |
Method of Test for Cement-Latex Compatibility |
| T 314 (PDF 224 KB) |
Method of Test for Photovolt Reflectance |
| T 318 (PDF 1.1 MB) |
Standard Operating Procedure for Melting of Flexible Bituminous Pavement Marker Adhesive for Evaluation |
| T 329 (PDF 1.3 MB) |
FOP for WSDOT for Moisture Content of Hot Mix Asphalt (HMA) by Oven Method |
| T 330 (PDF 235 KB) |
Method for Coatings (Pigmented Sealers) Used on Concrete Structures |
| T 335 (PDF 1.2 MB) |
FOP for AASHTO for Determining the Percentage of Fracture in Coarse Aggregate |
| T 404 (PDF 1.2 MB) |
Method of Test for Compressive Strength of Epoxy Resins |
| T 408 (PDF 1.3 MB) |
Method of Test for Quality of Water to be Used in Mixing Concrete |
| T 411 (PDF 1.0 MB) |
Method of Test for Water Absorption and Moisture Vapor Transpiration |
| T 412 (PDF 336 KB) |
Bond Test for Joint Sealants |
| T 413 (PDF 1.3 MB) |
Method of Test for Evaluating Waterproofing Effectiveness of Membrane and Membrane-Pavement Systems |
| T 414 (PDF 1.3 MB) |
Method of Test for Total Chloride Ion in Concrete |
| T 415 (PDF 1.0 MB) |
Method of Test for Fertilizer |
| T 417 (PDF 1.2 MB) |
Method of Test for Determining Minimum Resistivily and pH of Soil and Water |
| T 418 (PDF 1.0 MB) |
Method of test for Corrosion of Deicing Materials |
| T 419 (PDF 1.1 MB) |
Test Method for Cold Temperature Impact Resistance of the Plastic Coating on Reinforcing Bar Chair Feet |
| T 420 (PDF 1.2 MB) |
Test Method for Determining the Maturity of Compost (Solvita Test) |
| T 421 (PDF 1.2 MB) |
Test Method for Traffic Controller Inspection and Test Procedure |
| T 422 (PDF 1.2 MB) |
Test Method for Traffic Controller Transient Voltage Test (Spike Test) Procedure |
| T 423 (PDF 1.2 MB) |
Traffic Controller Conflict Monitor Testing |
| T 424 (PDF 1.1 MB) |
Traffic Controller Power Interruption Test Procedure |
| T 425 (PDF 1.2 MB) |
Traffic Controller NEMA and 170 Type Environmental Chamber Test |
| T 426 (PDF 1.1 MB) |
Pull-Off Test for Hot Melt Traffic Button Adhesive |
| T 427 (PDF 1.1 MB) |
Loop Amplifier Testing Procedure |
| T 428 (PDF 1.0 MB) |
Test Method for Traffic Controller Compliance Inspection and Test Procedure |
| SOP 429 (PDF 1.1 MB) |
Methods for Determining the Acceptance of Traffic Signal Controller Assembly |
| T 429 (PDF 1.1 MB) |
Retroreflectance of Newly Applied Pavement Marking Using Portable Hand-Operated Instruments |
| T 430 (PDF 1.1 MB) |
Method of Testing for the Presence of Adhesion Coating in Glass Beads |
| T 432 (PDF 1.0 MB) |
Flexibility Test for Hot-Melt Adhesives |
| T 601 (PDF 1.1 MB) |
Method of Test for Sieve Analysis of Soils-Coarse Sieving |
| T 606 (PDF 1.2 MB) |
Method of Test for Compaction Control of Granular Materials |
| T 610 (PDF 1.1 MB) |
Method of Test for the Capillary Rise of Soils |
| T 611 (PDF 625 KB) |
Method of Test for Determination of the Resistance (RValue) of Untreated Bases, Subbases, and Basement Soils by the Stabilometer |
| SOP 615 (PDF 1.2 MB) |
Determination of the % Compaction for Embankment & Untreated Surfacing Materials using the Nuclear Moisture-Density Gauge |
| T 702 (PDF 1.2MB) |
Method for Preparation of Test Specimens of Hot Mix Asphalt by Means of California Kneading Compactor |
| T 703 (PDF 1.1 MB) |
Method of Test for Resistance to Deformation of Hot Mix Asphalt by Means of HVEEM Stabilometer |
| T 706 (PDF 1.1 MB) |
Method of Static Immersion Asphalt in Water Preferential Stripping Test |
| T 712 (PDF 1.4 MB) |
Standard Method of Reducing Hot Mix Asphalt |
| T 716 (PDF 504 KB) |
Method of Random Sampling for Location of Testing and Sampling Sites |
| T 718 (PDF 1.1 MB) |
Method of Test for Determining Stripping of Hot Mix Asphalt |
| T 720 (PDF 242 KB) |
Method of Test for Thickness Measurement of Hot Mix Asphalt Cores |
| SOP 723 (PDF 1.0 MB) |
Standard Operating Procedure for Submitting Hot Mix Asphalt (HMA) Mix Designs for Verification |
| T 724 (PDF 321 KB) |
Method for Preparation of Aggregate for HMA Job Mix Design |
| T 726 (PDF 381 KB) |
Mixing Procedure for Hot Mix Asphalt |
| SOP 728 (PDF 1.0 MB) |
Standard Operating Procedure for Determining the Ignition Furnace Calibration Factor (IFCF) for Hot Mix Asphalt (HMA) |
| SOP 729 (PDF 1.1 MB) |
In-Place Density of Bituminous Mixes Using the Nuclear Moisture-Density Gauge FOP for WAQTC TM 8 |
| SOP 730 (PDF 336 KB) |
Standard Operating Procedure for Correlation of Nuclear Gauge Determined Density with Asphalt Concrete Pavement Cores |
| SOP 731 (PDF 486) |
Method for Determining Volumetric Properties of Asphalt Concrete Pavement Class Superpave |
| SOP 732 (PDF 1.6 MB) |
Standard Operating Procedure for Superpave Volumetric Design for Hot-Mix Asphalt (HMA) |
| SOP 733 (PDF 1.2 MB) |
Standard Operating Procedure for Determination of PavementDensity Differentials Using the Nuclear Density Gauge |
| SOP 734 (PDF 1.1 MB) |
Standard Operating Procedure for SAMPLING HOT MIX ASPHALT AFTER COMPACTION (OBTAINING CORES) |
| SOP 735 (PDF 1.1 MB) |
Standard Operating Procedure for Longitudinal Joint Density |
| T 802 (PDF 1.2 MB) |
Method of Test for Flexural Strength of Concrete (Using Simple Beam With Center-Point Loading) |
| C 805 (PDF 370 KB) |
Rebound Hammer Determination of Compressive Strength of Hardened Concrete |
| T 807 (PDF 1.3 MB) |
Method of Operation of California Profilograph and Evaluation of Profiles |
| T 808 (PDF 1.1 MB) |
Method for Making Flexural Test Beams |
| T 810 (PDF 325) |
Method of Test for Determination of the Density of Portland Cement Concrete Pavement Cores |
| T 812 (PDF 1.1 MB) |
Method of Test for Measuring Lenght of Drilled Concrete Cores |
| T 813 (PDF 1.1 mb) |
Field Method of Fabrication of 2 in (50 mm) Cube Specimens for Compressive Strength Testing of Grouts and Mortars |
| T 814 (PDF 1.1 MB) |
Method of Test for Water Retention Efficiency of Liquid Membrane-Forming Compounds and Impermeable Sheet Materials for Curing Concrete |
| T 816 (PDF 1.1 MB) |
Method of Test for Parting Compound |
| T 818 (PDF 1.0 MB) |
Air Content of Freshly Mixed Self-Compacting Concrete by the Pressure Method |
| T 819 (PDF 1.1 MB) |
Making and Curing Self-Compacting Concrete Test Specimens in the Field |
| C 882 (PDF 232 KB) |
Standard Test Method for Bond Strength of Epoxy-Resin Systems used with Concrete by Slant Shear |
| T 914 (PDF 1.2 MB) |
Practice for Sampling of Geotextiles for Testing |
| T 915 (PDF 1.1 MB) |
Practice for Conditioning of Geotextiles for Testing |
| T 923 (PDF 1.0 MB) |
Thickness Measurement of Geotextiles |
| T 925 (PDF 2.3 MB) |
Standard Practice for Determination of Long-Term Strength for Geosynthetic Reinforcement |
| T 926 (PDF 1.0 MB) |
Geogrid Brittleness Test |
| C 939 (PDF 297 KB) |
FOP for ASTM for Flow of Grout for Preplaced-Aggregate Concrete (Flow Cone Method) |
| C 1611 (PDF 330 KB) |
FOP for ASTM C 1611/C 1611M Standard Test Method for Slump Flow of Self-Consolidating Concrete |
| C 1621 (PDF 546 KB) |
FOP for ASTM C 1621/C 1621M Standard Test Method for Passing Ability of Self-Consolidating Concrete by J-Ring |
| D 2628/M 220 (PDF ) |
Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements (Checklist Only) |
| D 4354 (PDF 1.1 MB) |
Standard Practice for Sampling of Geosynthetics for Testing |
| D 4791 (PDF 2.4 MB) |
FOP for ASTM for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate |
| D 7012 (PDF 1.0 MB) |
Standard Test Method for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and Temperatures |
| D 7091 (PDF 217 KB) |
Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals (Checklist only) |